Home Improvement Ideas Outdoor Structures Your Guide to Repairing a Stone Wall with Seamless Results Learn how to repair damage to stone walls from frost heave, erosion, and deterioration to keep your wall looking as good as the day you built it. By Caitlin Sole Caitlin Sole Caitlin Sole is the senior home editor at BHG. She is a writer and editor with nearly a decade of interior design expertise. She has vast experience with digital media, including SEO, photo shoot production, video production, eCommerce content, print collaboration, and custom sales content. Learn about BHG's Editorial Process Published on June 18, 2018 Close Project Overview Total Time: 1 day Skill Level: Intermediate Many natural factors can damage stone walls. Erosion is the obvious choice, as is frost heave. And even though mortared walls are less subject to erosion because of their footing, their mortar jointsāand the surface of the stones themselvesācan crack and take in water, then freeze and split. A damaged wall that doesn't receive timely attention poses a safety hazard. You may be tempted to replace damaged stone with synthetic stone made from epoxy or cement-based materials. Such imitation stone is less expensive. Though the patches may look good at first, they will become conspicuous with further exposure to the elements and ultimately mar the appearance of the wall. We'll walk you through common stone wall repairs, including replacing a popped stone, rebuilding a damaged wall, repairing stone mortar joints, and more. What You'll Need Equipment / Tools 1 Wedges 1 Carpet-covered 2x4 1 Small sledgehammer 1 Crowbar 1 Marking chalk 1 Chisel 1 Mortar bag 1 Pointing trowel 1 Stiff brush 1 Circular saw and masonry blade Materials 1 Cracked rubble 1 Mortar Instructions Remove the Stone To return a popped stone to its original position, drive wedges between stable stones to take the weight off the popped stone. Work the popped stone out of the wall carefully, without dislodging the other stones. Drive the wedges into the wall slightly further. Reinsert Stone How to Repair Brick and Block Walls and Stop the Spread of Damage Reinsert the popped stone in its cavity and tap it home with a carpet-covered 2x4 and a small sledgehammer. Use a crowbar to take the weight off the wedges and remove them. You may have to work the wedges and the crowbar back out of the wall at the same time.Editor's tip: To ensure the longevity of your wall, look to the landscaping. Climbing plants pose no danger to hardened mortar, but roots disturb footings and tendrils take hold in cracks. Plant life in the wrong places displaces stones or bricks, blocks rainwater runoff, and hides other damage. To remove plants, cut the main stem above ground level and treat it with a product recommended by your local extension service. However, residues of some weed killers can cause spalling on some stone surfaces. If stone-faced steps are worn, you may be able to reuse them by turning them over. Mark Area A collapsed section of wall can often be repaired without total replacement. Inspect the wall and visualize a V-shape section that you'll need to remove. Mark the area on the wall with marking chalkādon't use spray paint. Then number the stones with chalk so you can replace them to their original positions. Take a photo of the wall to further help you replace the stones in the right order. Chisel Mortar Working above the marked section, chisel away any mortar that anchors the capstones and take them off the wall. Dismantle the damaged section. Clean Stones (Optional) Before you reinstall the stones, check if they need to be cleaned. If they do, choose the most gentle cleaning method that can handle the job. Start with water cleaning, the most gentle method, then turn to chemical-base cleaners or mechanical methods such as sandblasting only if you need to. A pressure washer can be an effective cleaning method, but also may erode softer stones like sandstone. Keep in mind that water increases damage to badly deteriorated mortar. Repair the mortar before cleaning with water. Steam cleaning is an effective method for removing embedded soil and poses less risk than sandblasting. Sandblasting is a method of last resort. A poultice of absorbent material mixed with a solvent can remove many chemical stains without damaging the stone. Keep the poultice on the stain as long as necessary to remove the stain. As a rule of thumb, always test your cleaning agent in an inconspicuous spot before using it on the entire surface. Rebuild Wall Using your snapshot as a guide, rebuild the wall, working from the leads toward the center. Set the stones using the same techniques used to build it. Be sure to replace any small stones used to keep larger ones in place. Fill in the center recess between the wythes with cracked rubble. Replace the capstones. Chip Out Mortar Carefully chip out the damaged mortar with a thin cold chisel and a small sledgehammer. Clean the joint until you reach solid mortar. Mix New Mortar Mix new mortar to a consistency for use with a mortar bag and fill the bag. Mist the joint with water from a spray bottle and squeeze mortar into the joints. Editor's tip: If you repair masonry with mortar that doesn't match the original, it will really stand out. Matching the tint of existing mortar takes some experimenting and patience. You can't tell what the new mortar will look like until it has dried. Mix up the mortar in several batches and spread out thin amounts to dry. Pick the dried color that best matches the original. Pack Each Joint Pack each joint tightly with a pointing trowel, adding more mortar if necessary. Tool the joints to match the original and remove excess mortar with a stiff brush.Editor's tip: It's important to pack mortar tightly. Otherwise, the wall will be more susceptible to erosion. Soil erosion is often the cause of a toppled wall section. This is a problem that does not usually show up for many years. To repair the damage, remove stones from the damaged area and at least two stones wider. Dig a 6- to 8-inch trench where you have removed the stones. Fill the trench with gravel a little at a time and tamp it as you go. Rebuild the section of wall. The gravel will allow water to drain under the wall without washing out its support. Remove Damaged Stone Remove the damaged stone by chiseling out the mortar around the stone. Angle the chisel in the direction of the damaged stone to avoid damaging others. Then pry out the stone. Using a wider cold chisel, remove as much mortar as possible from the cavity. Brush or blow out the cavity to remove loose mortar and dust (wear eye protection). Mark Cut Lines Hold a new stone slightly larger than the recess against the wall and mark cut lines so you can cut it to fit properly. Cut Stone to Size If the stone is thin enough, cut it with a circular saw and masonry blade. Then using a mason's hammer, carefully chip the replacement stone until it fits the recess with enough space for the mortar joints. Be careful not to cut too much off the stone; doing so makes the joints wider than those on the rest of the surface and calls attention to the repair. How to Build a Rock Wall With Mortar and Line Your Yard With Charm Insert Stone Mist the cavity and spread mortar on the bottom of the cavity and the top and sides of the replacement stone. Insert the stone and push it into place using the pointing trowel. Pack mortar against all sides of the stone. When the mortar has set, tool it to match the original. How to Build a Mortarless Stone Wall in 5 Simple Steps